View EDI7P004FVA0300C15_2386647.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

august 2000 rev. 3 - eco #13134 1 pcmcia flash memory card fva series pc card products features ? low cost linear flash card ? single 5 volt supply ?based on flashfile tm components ?fast read performance - 100ns or 150ns maximum access time ? x16 data interface - odd byte not accessible on even byte ? high performance random writes - 10s typical word write time ? automated write and erase algorithms - intel command set ? 50a typical deep power-down ? 100,000 erase cycles per block ? 64k word symmetrical block architecture ? pc card standard type i form factor the wedc value series (fv) flash memory cards offers a low cost linear flash solid state storage solution for code and data storage, high performance disk emulation, mobile pc and embedded applications. the wedc value series is based on intel/sharp flash memories. cards are based on the 28f008sa (8mb), 28f008s5 (8mb) or 28f016s5 (16mb) devices whose device codes are a2h, a6h and aah respectively. systems should be able to recognize all three codes. the symmetrically blocked architecture and single 5v operation provides a cost effective, high performance, nonvolatile storage solution. the pc card form factor offers an industry standard pinout and mechanical outline, allowing density upgrades without system design changes. the value series is designed as a simple x16 linear array of flash devices. two flash devices in parallel provide the lower and upper bytes for the 16 bit access. the value series does not provide access of the odd byte (d8 - d15) on the even byte data path (d0 - d7). wedc?s standard value series flash card is shipped with no attribute memory or cis (card information structure) information. an option for 2kb of attribute memory with cis information is available. the cis for the wedc value series may also be stored in block 0 (even bytes, d0 - d7 only) of the flash memory, this option is available by request only. wedc?s standard cards are shipped with wedc?s logo. cards are also available with blank housings (no logo). the blank housings are available in both a recessed (for label) and flat housing. please contact wedc sales representative for further information on custom artwork. value series flash memory card 2, 4, 8, 16 megabyte (intel/sharp based ) block diagram note: vpp generator only required for cards using 28f008sa devices configuration above for 8mb card using 8mbit components. address bus a1-a20 data d0-7 data d8-15 attribute memory 28c16 control logic /ce1 /ce2 /reg /we /oe a21 a22 device 1 device 3 device 5 device 7 device 0 device 2 device 4 device 6 vpp generator vcc vcc vpp vpp1 vpp2 vs1 vs2 open /wr /rd rdy/bsy busy 0-7 general description
august 2000 rev. 3 - eco #13134 2 pcmcia flash memory card fva series pc card products pin signal name i/o function active pin signal name i/o function active 1 gnd ground 35 gnd ground 2 dq3 i/o data bit 3 36 cd1# o card detect 1 low 3 dq4 i/o data bit 4 37 dq11 i/o data bit 11 4 dq5 i/o data bit 5 38 dq12 i/o data bit 12 5 dq6 i/o data bit 6 39 dq13 i/o data bit 13 6 dq7 i/o data bit 7 40 dq14 i/o data bit 14 7 ce1# i card enable 1 low 41 dq15 i data bit 15 8 a10 i address bit 10 42 ce2# i card enable 2 low 9 oe# i output enable low 43 vs1 o voltage sense 1 n.c. 10 a11 i address bit 11 44 rfu reserved 11 a9 i address bit 9 45 rfu reserved 12 a8 i address bit 8 46 a17 i address bit 17 13 a13 i address bit 13 47 a18 i address bit 18 14 a14 i address bit 14 48 a19 i address bit 19 15 we# i write enable low 49 a20 i address bit 20 2mb(2) 16 rdy/bsy # o ready/busy low 50 a21 i address bit 21 4mb(2) 17 vcc supply voltage 51 vcc supply voltage 18 vpp1 prog. voltage n.c. 52 vpp2 prog. voltage n.c. 19 a16 i address bit 16 53 a22 i address bit 22 8mb(2) 20 a15 i address bit 15 54 a23 i address bit 23 16mb(2) 21 a12 i address bit 12 55 a24 i address bit 24 n.c. 22 a7 i address bit 7 56 a25 i address bit 25 n.c. 23 a6 i address bit 6 57 vs2 o voltage sense 2 n.c. 24 a5 i address bit 5 58 rst i card reset high 25 a4 i address bit 4 59 wait# o e xtended bus cycl e low 26 a3 i address bit 3 60 rfu reserved 27 a2 i address bit 2 61 reg# i attrib mem select 28 a1 i address bit 1 62 bvd2 o bat. volt. detect 2 29 a0 i address bit 0 n.c. 63 bvd1 o bat. volt. detect 1 30 dq0 i/o data bit 0 64 dq8 i/o data bit 8 31 dq1 i/o data bit 1 65 dq9 i/o data bit 9 32 dq2 i/o data bit 2 66 dq10 o data bit 10 33 wp o write potect high 67 cd2# o card detect 2 low 34 gnd ground 68 gnd ground pinout notes: 1. rdy/bsy signal is a full cmos output, pull-up resistors are not required. 2. shows density for which specified address bit is msb. higher order address bits are no connects (ie 4mb a21 is msb a22 - a25 are nc). mechanical 54.0mm 0.10 (2.126?) 10.0mm min (0.400?) 1.6mm 0.05 (0.063?) 1.0mm 0.05 (0.039?) 1.0mm 0.05 (0.039?) 3.3mm t1 (0.130?) t1=0.10mm interconnect area t1=0.20mm substrate area interconnect area 10.0mm min (0.400?) 3.0mm min 85.6mm 0.20 (3.370?) substrate area
august 2000 rev. 3 - eco #13134 3 pcmcia flash memory card fva series pc card products symbol type name and function a0 - a25 input address inputs: a0 through a25 enable direct addressing of up to 64mb of memory on the card. signal a0 is not decoded since the card is x16 only. the memory will wrap at the card density boundary. the system should not try to access memory beyond the card density. the upper addresses are not connected. dq0 - dq15 input/outp ut data input/output: dq0 through dq15 constitute the bi-directional databus. dq0 - dq7 constitute the lower (even) byte and dq8 - dq15 the upper (odd) byte. dq15 is the msb. ce1#, ce2# input card enable 1 and 2: ce1# enables even byte accesses, ce2# enables odd byte accesses. odd byte (dq8 - dq15) can not be accessed on dq0 - dq7. oe# input output enable: active low signal enabling read data from the memory card. we# input write enable: active low signal gating write data to the memory card. rdy/bsy# output ready/busy output: indicates status of internally timed erase or program algorithms. a high output indicates that the card is ready to accept accesses. cd1#, cd2# output card detect 1 and 2: provide card insertion detection. these signals are connected to ground internally on the memory card. the host socket interface circuitry shall supply 10k-ohm or larger pull-up resistors on these signal pins. wp output write protect: this signal is pulled low internally. this signifies write protect = "off " for all cases. vpp1, vpp2 n.c. program/erase power supply: not connected for 5v only card. vcc card power supply: 5.0v for all internal circuitry. gnd ground: for all internal circuitry. reg# input attribute memory select : only used with cards built with optional attribute memory. rst input reset: active high signal for placing card in power-on default state. reset can be used as a power-down signal for the memory array. wait# output wait: this signal is pulled high internally for compatibility. no wait states are generated. bvd1, bvd2 output battery voltage detect: these signals are pulled high to maintain sram card compatibility. vs1, vs2 output voltage sense: notifies the host socket of the card's vcc requirements. vs1 and vs2 are open to indicate a 5v, 16 bit card has been inserted. rfu reserved for future use n.c. no internal connection to card: pin may be driven or left floating card signal description read function common memory attribute memory function mode /ce2 /ce1 /oe /we /reg d15-d8 d7-d0 /reg d15-d8 d7-d0 standby mode hhxx x high-z high-z x high-z high-z low byte access hllh h high-z even-byte l high-z even-byte word access (16 bits) lllh h odd-byte even-byte l not valid even-byte odd-byte only access lhlh h odd-byte high-z l not valid high-z write function standby mode hhxx x xx x xx low byte access hlhl h xeven-byte l xeven-byte word access (16 bits) llhl h odd-byte even-byte l xeven-byte odd-byte only access lhhl h odd-byte x l xx functional truth table
august 2000 rev. 3 - eco #13134 4 pcmcia flash memory card fva series pc card products absolute maximum ratings (2) operating temperature ta (ambient) commercial 0c to +60 c industrial -40c to +85 c storage temperature -55c to +110 c voltage on any pin relative to vss -0.5v to vcc+0.5v (1) vcc supply voltage relative to vss -0.5v to +7.0v notes: (1) during transitions, inputs may undershoot to -2.0v or overshoot to vcc +2.0v for periods less than 20ns. (2) stress greater than those listed under ?absolute maximum ratings? may cause permanent damage to the device. this is a stress rating only and functional operation at these or any other conditions greater than those indicated in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect reliability. symbol parameter density (mbytes) notes typ (3) max units test conditions iccr vcc read current 2,4,8,16 75 ma vcc = 5.25v tcycle = 100ns iccw vcc program current 2,4,8,16 100 ma icce vcc erase current 2,4,8,16 100 ma iccsl vcc sleep current 2,4,8 2 50 160 a vcc = 5.25v control signals = vcc reset = vih iccsl vcc sleep current 16 2 90 240 a vcc = 5.25v control signals = vcc reset = vih iccs vcc standby current 2,4,8,16 2 3 10 ma vcc = 5.25v control signals = vcc notes: 1. all currents are for x16 mode and are rms values unless otherwise specified. 2. control signals: ce 1 #, ce 2 #, oe#, we#, reg#. 3. typical: vcc = 5v, t = +25c. cmos test conditions: vil = vss 0.2v, vih = vcc 0.2v dc characteristics (1) symbol parameter notes min max units test conditions ili input leakage current 1,2 20 a vcc = vccmax vin =vcc or vss ilo output leakage current 1 20 a vcc = vccmax vout =vcc or vss vil input low voltage 1 0 0.8 v vih input high voltage 1 3.85 vcc+0.5 v vol output low voltage 1 0.4 v iol = 3.2ma voh output high voltage 1 vcc-0.4 vcc v ioh = -2.0ma vlko vcc erase/program lock voltage 12.0 v notes: 1. values are the same for byte and word wide modes for all card densities. 2. exceptions: leakage currents on ce1#, ce2#, oe#, reg# and we# will be < 500 a when vin = gnd due to internal pull-up resistors. leakage currents on rst will be <150a when vin=vcc due to internal pull-down resistor.
august 2000 rev. 3 - eco #13134 5 pcmcia flash memory card fva series pc card products note 1 note 1 a [25::0], /reg /ce1, /ce2 /oe d[15::0] tc(r) ta(a) th(a) tv(a) ta(ce) tsu(ce) th(ce) ten(oe) ta(oe) tsu(a) data valid tdis(ce) tdis(oe) 100ns (2) 150ns symbol (pcmcia) parameter min max min max unit t c (r) read cycle time 100 150 ns t a (a) address access time 100 150 ns t a (ce) card enable access time 100 150 ns t a (oe) output enable access time 50 75 ns t su (a) address setup time 10 20 ns t su (ce) card enable setup time 0 0 ns t h (a) address hold time 15 20 ns t h (ce) card enable hold time 15 20 ns t v (a) output hold from address change 0 0 ns t dis (ce) output disable time from ce# 50 75 ns t dis (oe) output disable time from oe# 50 75 ns t en (ce) output enable time from ce# 5 5 ns t en (oe) output enable time from oe# 5 5 ns t rec(rst) power down recovery to output delay. vcc = 5v 500 500 ns ac characteristics notes: 1. ac timing diagrams and characteristics are guaranteed to meet or exceed pcmcia 2.1 specifications. 2. valid for cards using 8mb components (28f008sa or 28f008s5)only. cards based on 16mb (28f016) are available as 150ns cards only. read timing diagram read timing parameters (1) note: signal may be high or low in this area.
august 2000 rev. 3 - eco #13134 6 pcmcia flash memory card fva series pc card products 100n s (2) 150n s symbol (pcmcia) parameter min max min max unit t c w write cycle time 100 150 ns t w (we) write pulse width 60 80 ns t su (a) address setup time 10 20 ns t su (a-weh) address setup time for we# 70 100 ns t su (ce-weh) card enable setup time for we# 70 100 ns t su (d-weh) data setup time for we# 40 50 ns t h (d) data hold time 15 20 ns t rec (we) write recover time 15 20 ns t dis (we) output disable time from we# 50 75 ns t dis (oe) output disable time from oe# 50 75 ns t en (we) output enable time from we# 5 5 ns t en (oe) output enable time from oe# 5 5 ns t su (oe-we) output enable setup from we# 10 10 ns t h (oe-we) output enable hold from we# 10 10 ns t su (ce) card enable setup time from oe# 0 0 ns t h (ce) card enable hold time 15 20 ns notes: 1. ac timing diagrams and characteristics are guaranteed to meet or exceed pcmcia 2.1 specifications. 2. valid for cards using 8mb components (28f008sa or 28f008s5)only. cards based on 16mb (28f016) are available as 150ns cards only. write timing diagram write timing parameters (1) th (o e -w e ) note 1 /c e 1 , /c e 2 note 1 ts u (c e -w e h ) tc(w ) a [2 5::0 ], /r e g tw (w e ) td is(w e ) th (d ) d[15::0](din) d a t a in p u t ts u (a ) ts u (a -w e h ) /o e tsu (c e ) tsu(d -w e h ) trec(w e ) th (c e ) tsu (o e -w e ) td is(o e ) d[15::0](dout) ten (o e ) te n(w e ) note 2 note 2 /w e notes: 1. signal may be high or low in this area. 2. when the data i/o pins are in the output state, no signals shall be applied to the data pins (d15 - d0) by the host system.
august 2000 rev. 3 - eco #13134 7 pcmcia flash memory card fva series pc card products sym parameter notes min typ (1) max units test conditions t whqv1 t ehqv1 word/byte program time 2,4 8s 3ms t whqv2 t ehqv2 block program time 2 0.4 2.1 sec word program mode block erase time 2 0.6 10 sec full chip erase time 2, 5 38.4 sec data write and erase performance (1,3) notes: 1. typical: nominal voltages and t a = 25c. 2. excludes system overhead. 3. valid for all speed options. 4. to maximize system performance rdy/bsy# signal or component status register should be polled. 5. chip erase time based on 8 mbit flash components (28f008sa). vcc = 5v 5%, t a = 0c to + 60c sym parameter notes min typ (1) max units test conditions t whqv1 t ehqv1 word/byte program time 2,4 8s 3ms t whqv2 t ehqv2 block program time 2 0.5 tbd sec word program mode block erase time 2 1.1 tbd sec full chip erase time 2, 5 38.4 sec notes: 1. typical: nominal voltages and t a = 25c. 2. excludes system overhead. 3. valid for all speed options. 4. to maximize system performance rdy/bsy# signal or component status register should be polled. 5. chip erase time based on 8 mbit flash components (28f008s5). vcc = 5v 5%, t a = 0c to + 60c 28f008sa based flash cards 28f008s5 and 28f016s5 based flash cards
august 2000 rev. 3 - eco #13134 8 pcmcia flash memory card fva series pc card products edi company name lot code / trace number date code part number product marking wed 7p016fva0600c15 c995 9915 note: some products are currently marked with our pre-merger company name/acronym (edi). during our transition period, some products will also be marked with our new company name/acronym (wed). starting october 2000 all pcmcia products will be marked only with the wed prefix. card capacity 016 16mb packaging option 00 standard, type 1 pc card p standard pcmcia r ruggedized pcmcia card family and version - see card family and version info. for details (next page) temperature range c commercial 0c to +70c i industrial -40c to +85c card access time 15 150ns 25 250ns card technology 7flash 8sram part numbering 7 p 016 fva06 00 c 15
august 2000 rev. 3 - eco #13134 9 pcmcia flash memory card fva series pc card products 7p xxx fva yy ss t zz where xxx: 002 2mb 004 4mb 008 8mb 016 16mb (uses 28f016s5 only) yy: 01 28f008sa base 02 28f008sa w/attribute memory 03 28f008s5 base 04 28f008s5 w/attribute memory 05 28f016s5 base 06 28f016s5 w/attribute memory ss: 00 wedc silkscreen 01 blank housing, type i 02 blank housing, type i recessed t: c commercial i industrial zz: 10 100ns 15 150ns ordering information part number table - common options notes: 1. cards built with 16mb devices are not available in 100ns speed grade. 2. other options, including density, architecture and speed are available, please contact your wedc sales representative with your request. wedc part number density speed flash component attribute memory intel/sharp based cards edi7p002fva0100c10 2mb 100ns 28f008sa no edi7p002fva0100c15 2mb 150ns 28f008sa no edi7p002fva0300c10 2mb 100ns 28f008s5 no edi7p002fva0300c15 2mb 150ns 28f008s5 no edi7p002fva0200c10 2mb 100ns 28f008sa 2k eeprom edi7p002fva0200c15 2mb 150ns 28f008sa 2k eeprom edi7p002fva0400c10 2mb 100ns 28f008s5 2k eeprom edi7p002fva0400c15 2mb 150ns 28f008s5 2k eeprom EDI7P004FVA0300C15 4mb 150ns 28f016s5 no edi7p004fva0400c15 4mb 150ns 28f016s5 2k eeprom edi7p008fva0300c15 8mb 150ns 28f016s5 no edi7p008fva0400c15 8mb 150ns 28f016s5 2k eeprom edi7p016fva0500c15 16mb 150ns 28f016s5 no edi7p016fva0600c15 16mb 150ns 28f016s5 2k eeprom
august 2000 rev. 3 - eco #13134 10 pcmcia flash memory card fva series pc card products address value description 00h 01h cistpl_device 02h 03h tpl_link 04h 54h flash = 100ns (device writable) 53h flash = 150ns (device writable) 06h 06h card size: 2mb 0eh 4mb 1eh 8mb 08h ffh end of device 0ah 18h cistpl_jedec_a 0ch 02h tpl_link 0eh 89h intel - id 10h a2h intel 28f008sa - id 12h 17h cistpl_device_a 14h 03h tpl_link 16h 42h eeprom - 200ns 18h 01h device size = 2kbytes 1ah ffh end of tuple 1ch 1eh cistpl_devicegeo 1eh 06h tpl_link 20h 02h dgtpl_bus 22h 11h dgtpl_ebs 24h 01h dgtpl_rbs 26h 01h dgtpl_wbs 28h 01h dgtpl_part 2ah 01h flash device non-interleaved 2ch 20h cistpl_manfid 2eh 04h tpl_link(04h) 30h f6h edi tplmid_manf: lsb 32h 01h edi tplmid_manf: msb 34h 00h lsb: number not assigned 36h 00h msb: number not assigned 38h 15h cistpl_vers1 3ah 4ah tpl_link 3ch 05h tpllv1_major 3eh 00h tpllv1_minor 40h 45h e 42h 44h d 44h 49h i 46h 37h 7 48h 50h p 4ah 30h 0 4ch 30h 0 4eh x 50h 46h f 52h 56h v 54h 41h a 56h 30h 0 58h 32h 2 5ah 2dh - 5ch 2dh - 5eh 2dh - 60h y 62h y address value description 64h 20h space 66h 00h end text 68h 43h c 6ah 4fh o 6ch 50h p 6eh 59h y 70h 52h r 72h 49h i 74h 47h g 76h 48h h 78h 54h t 7ah 20h space 7ch 45h e 7eh 4ch l 80h 45e e 82h 43h c 84h 54h t 86h 52h r 88h 4fh o 8ah 4eh n 8ch 49h i 8eh 43h c 90h 20h space 92h 44h d 94h 45h e 96h 53h s 98h 49h i 9ah 47h g 9ch 4eh n 9eh 53h s a0h 20h space a2h 49h i a4h 4eh n a6h 43h c a8h 4fh o aah 52h r ach 50h p aeh 4fh o b0h 52h r b2h 41h a b4h 54h t b6h 45h e b8h 44h d bah 20h space bch 00h end text beh 31h 1 c0h 39h 9 c2h 39h 9 c4h 37h 7 c6h 00h end text c8h ffh end of list cah ffh cistpl_end cch 00h invalid address cis data - cards based on 28f008sa components with attribute memory note: in the part number, value x will be substituted with the proper capacity and value yy with the proper card speed.
august 2000 rev. 3 - eco #13134 11 pcmcia flash memory card fva series pc card products cis data - cards based on 28f008s5 components with attribute memory address value description 00h 01h cistpl_device 02h 03h tpl_link 04h 54h flash = 100ns (device writable) 53h flash = 150ns (device writable) 06h 06h card size: 2mb 0eh 4mb 1eh 8mb 08h ffh end of device 0ah 18h cistpl_jedec_c 0ch 02h tpl_link 0eh 89h intel - id 10h a6h intel 28f008s5 - id 12h 17h cistpl_device_a 14h 03h tpl_link 16h 42h eeprom - 200ns 18h 01h device size = 2kbytes 1ah ffh end of tuple 1ch 1eh cistpl_devicegeo 1eh 06h tpl_link 20h 02h dgtpl_bus 22h 11h dgtpl_ebs 24h 01h dgtpl_rbs 26h 01h dgtpl_wbs 28h 01h dgtpl_part 2ah 01h flash device non-interleaved 2ch 20h cistpl_manfid 2eh 04h tpl_link(04h) 30h f6h edi tplmid_manf: lsb 32h 01h edi tplmid_manf: msb 34h 00h lsb: number not assigned 36h 00h msb: number not assigned 38h 15h cistpl_vers1 3ah 47h tpl_link 3ch 05h tpllv1_major 3eh 00h tpllv1_minor 40h 45h e 42h 44h d 44h 49h i 46h 37h 7 48h 50h p 4ah 30h 0 4ch 30h 0 4eh x 50h 46h f 52h 56h v 54h 41h a 56h 30h 0 58h 34h 4 5ah 2dh - 5ch 2dh - 5eh 2dh - 60h y 62h y address value description 64h 20h space 66h 00h end text 68h 43h c 6ah 4fh o 6ch 50h p 6eh 59h y 70h 52h r 72h 49h i 74h 47h g 76h 48h h 78h 54h t 7ah 20h space 7ch 45h e 7eh 4ch l 80h 45e e 82h 43h c 84h 54h t 86h 52h r 88h 4fh o 8ah 4eh n 8ch 49h i 8eh 43h c 90h 20h space 92h 44h d 94h 45h e 96h 53h s 98h 49h i 9ah 47h g 9ch 4eh n 9eh 53h s a0h 20h space a2h 49h i a4h 4eh n a6h 43h c a8h 4fh o aah 52h r ach 50h p aeh 4fh o b0h 52h r b2h 41h a b4h 54h t b6h 45h e b8h 44h d bah 20h space bch 00h end text beh 31h 1 c0h 39h 9 c2h 39h 9 c4h 37h 7 c6h 00h end text c8h ffh end of list cah ffh cistpl_end cch 00h invalid address note: in the part number, value x will be substituted with the proper capacity and value yy with the proper card speed.
august 2000 rev. 3 - eco #13134 12 pcmcia flash memory card fva series pc card products cis data - cards based on 28f016s5 components with attribute memory address value description 00h 01h cistpl_device 02h 03h tpl_link 04h 53h flash = 150ns (device writable) 06h 0eh card size: 4mb 1eh 8mb 3eh 16mb 08h ffh end of device 0ah 18h cistpl_jedec_c 0ch 02h tpl_link 0eh 89h intel - id 10h aah 28f016s5 - id 12h 17h cistpl_device_a 14h 03h tpl_link 16h 42h eeprom - 200ns 18h 01h device size = 2kbytes 1ah ffh end of tuple 1ch 1eh cistpl_devicegeo 1eh 06h tpl_link 20h 02h dgtpl_bus 22h 11h dgtpl_ebs 24h 01h dgtpl_rbs 26h 01h dgtpl_wbs 28h 01h dgtpl_part 2ah 01h flash device non-interleaved 2ch 20h cistpl_manfid 2eh 04h tpl_link(04h) 30h f6h edi tplmid_manf: lsb 32h 01h edi tplmid_manf: msb 34h 00h lsb: number not assigned 36h 00h msb: number not assigned 38h 15h cistpl_vers1 3ah 47h tpl_link 3ch 05h tpllv1_major 3eh 00h tpllv1_minor 40h 45h e 42h 44h d 44h 49h i 46h 37h 7 48h 50h p 4ah 30h 0 4ch 30h 0 4eh x 50h 46h f 52h 56h v 54h 41h a 56h 30h 0 58h 36h 6 5ah 2dh - 5ch 2dh - 5eh 2dh - 60h y 62h y address value description 64h 20h space 66h 00h end text 68h 43h c 6ah 4fh o 6ch 50h p 6eh 59h y 70h 52h r 72h 49h i 74h 47h g 76h 48h h 78h 54h t 7ah 20h space 7ch 45h e 7eh 4ch l 80h 45e e 82h 43h c 84h 54h t 86h 52h r 88h 4fh o 8ah 4eh n 8ch 49h i 8eh 43h c 90h 20h space 92h 44h d 94h 45h e 96h 53h s 98h 49h i 9ah 47h g 9ch 4eh n 9eh 53h s a0h 20h space a2h 49h i a4h 4eh n a6h 43h c a8h 4fh o aah 52h r ach 50h p aeh 4fh o b0h 52h r b2h 41h a b4h 54h t b6h 45h e b8h 44h d bah 20h space bch 00h end text beh 31h 1 c0h 39h 9 c2h 39h 9 c4h 37h 7 c6h 00h end text c8h ffh end of list cah ffh cistpl_end cch 00h invalid address note: in the part number, value x will be substituted with the proper capacity and value yy with the proper card speed.
august 2000 rev. 3 - eco #13134 13 pcmcia flash memory card fva series pc card products revision rev date description 0 jan-98 initial release 1 jun-99 logo/name change 2 may-00 added pg. 8 3 aug-00 changed pg. 5&6 revision history white electronic designs corporation one research drive, westborough, ma 01581, usa tel: (508) 366 5151 fax: (508) 836 4850 www.whiteedc.com

▲Up To Search▲

Price & Availability of EDI7P004FVA0300C15

	To Download EDI7P004FVA0300C15 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .